Beginner-Friendly Crochet Strawberry Coaster Pattern

A crochet strawberry coaster is a small cotton project that looks cheerful on a summer table and still stays practical under a glass or mug. This version makes one flat strawberry-shaped coaster with a red berry body, a green leafy cap, and tiny white seed stitches.

The pattern is written for beginners who are comfortable with basic stitches. Keep your tension firm so the coaster holds its shape and the cup sits evenly.

Materials

• Worsted cotton yarn in red, green, and white
• 4 mm crochet hook, or a hook size that gives you firm flat stitches
• Yarn needle
• Scissors
• Optional blocking mat and rust-proof pins

Abbreviations

• ch = chain
• sl st = slip stitch
• sc = single crochet
• hdc = half double crochet
• dc = double crochet
• inc = work 2 stitches into the same stitch
• st = stitch
• rep = repeat

Finished Size

Your coaster should finish around 4 to 5 inches tall, depending on yarn, hook size, and blocking. The shape should be wide at the top, softly rounded at the shoulders, and gently pointed at the bottom.

Step-by-Step Instructions

Step 1: Start the Red Berry Body

1. With red yarn, ch 4.
2. Work 2 sc in the second ch from the hook.
3. Work 1 sc in the next ch.
4. Work 3 sc in the last ch so you can turn around the foundation.
5. Continue along the other side of the chain with 1 sc in the next ch and 1 sc in the last ch. Join with sl st if you prefer closed rounds.

This gives you a small oval base that will become the lower point of the strawberry.

Step 2: Widen the Strawberry Shape

1. Round 2: Ch 1, work 2 sc in the first st, sc across the side, work 2 sc in each of the 3 stitches around the top curve, sc down the other side, and join.
2. Round 3: Ch 1, sc around, placing extra increases across the top curve only. Keep the lower end narrower than the top.
3. Round 4: Repeat another round of sc, adding 4 to 6 increases across the upper half so the shoulders look rounded.
4. Lay the piece flat. If the bottom looks too round, pinch it gently into a soft point before continuing.

Step 3: Smooth the Edge

1. Work one final round of red sc around the berry body.
2. At the bottom point, work sl st, sc, sl st across the lowest stitches to make the point look cleaner.
3. Fasten off red yarn and weave in the tail on the back.

Step 4: Add the Green Leafy Cap

1. Join green yarn at the upper left edge of the strawberry.
2. Ch 1 and sc across the top edge.
3. Make the first leaf point: ch 4, sl st in the second ch from the hook, sc in the next ch, hdc in the next ch, then sl st into the next top-edge stitch.
4. Repeat the leaf point 3 to 5 times across the top, depending on the width of your coaster.
5. Fasten off and weave in the green ends securely.

Step 5: Embroider the Seeds

1. Thread a yarn needle with a short length of white cotton yarn.
2. Make tiny vertical seed stitches across the red berry body.
3. Space the seeds in staggered rows so they look natural.
4. Keep each seed small and flat. Thick knots can make cups wobble.
5. Secure the white yarn on the back and trim the end.

Step 6: Block the Coaster Flat

1. Lightly mist the coaster with water.
2. Pin the berry point, rounded shoulders, and leaf tips into shape.
3. Let it dry fully before using it under a drink.

Tips for a Better Finished Coaster

• Use cotton yarn because it absorbs light moisture better than acrylic.
• Choose a smaller hook if the fabric feels loose or floppy.
• Keep the white seed stitches flat so glasses sit evenly.
• Make a matching set by repeating the same yarn, hook, and tension.
• For a softer look, make one coaster in coral or pink and keep the same green leaf top.

Care Notes

Hand wash or spot clean the coaster when possible. Reshape the strawberry while damp, flatten the leaf tips, and let it dry completely before stacking it with other coasters.

Final Note

This pattern works best as a single beginner-friendly fruit coaster or as a repeated set of four. Once the first coaster lies flat, use it as your size guide for the rest of the set.